Stone Slab Rack for Granite & Marble Yards
Store granite and marble slabs upright in an L-frame layout with felt-lined contact points, a counterweight-based anti-tip structure, and forklift access. The 15742 stone-direction reference is 2400 × 750 × 1200 mm for 4 × 8 ft panels and a 1,000 kg rated load. Submit your slab dimensions and tonnage for a layout matched to your yard.
Send slab size and tonnage
A vertical granite storage rack built around edge protection and stable loading
Stone yards handle dense, expensive slabs with sharp, vulnerable edges. A wall-side L-frame stone slab rack keeps slabs upright rather than spread across the floor, leaves a defined forklift approach, and gives the load a controlled support line. The result depends on the selected rack model, contact protection, base geometry, and the actual slab mix—not on a single universal capacity number.
15742 stone slab rack starting point
Use this stone-direction reference for early layout discussion. Final rating, protective lining, forkway, and anchoring requirements must be checked against your slab weight, dimensions, handling equipment, floor, and operating method.
| Item | 15742 stone-direction reference | What to confirm before ordering |
|---|---|---|
| Overall size | 2400 × 750 × 1200 mm | Slab length, width, thickness, overhang, and available aisle depth |
| Rated load | 1000 kg for this reference configuration | Actual slab bundle weight and the selected model rating; do not apply this value to every Grack model |
| Reference self-weight | 112 kg | Final frame, lining, options, and transport configuration |
| Panel fit | 4 × 8 ft panels | Whether your 4 × 8 ft slabs are individual, bundled, finished, or mixed with other sizes |
| Loading method | Upright placement into the L-frame support | Fork width, fork entry height, pallet-jack clearance, and loading sequence |
| Contact protection | Felt-lined stone contact points for the 15742 direction | Felt specification, replacement method, edge condition, and whether an EPDM profile is required for another configuration |
| Outdoor finish | Hot-dip galvanizing available as an option | Exposure, drainage, mud, washdown, coating requirement, and any local corrosion specification |

Size the rack from the slab, not from a catalogue guess
Send the largest slab, typical bundle weight, number of slabs per rack, forklift details, and indoor or outdoor location. We can then review upright spacing, base depth, forkway position, protective contact surfaces, and any ballast or fixing requirement.
- 4 × 8 ft slab layout review
- Model-specific load and base check
- Indoor coating or optional hot-dip galvanizing discussion
Four decisions that control chip risk and handling stability
The rack is a reusable handling asset. It is suitable where slabs need controlled upright storage and mechanical movement, provided the load, floor, equipment, and protective interface are matched to the selected design.
1. Upright storage keeps the slab footprint defined
Granite and marble are stored on edge against the L-frame support instead of lying across a large floor area. The 85°–87° loaded support angle used in Grack designs gives the slab a controlled rearward lean while the base takes the vertical load. For 4 × 8 ft panels, the 15742 reference provides a 2400 mm rack length; the actual number of slabs depends on thickness, separators, loading method, and the approved load rating. Do not treat the rack as a free-standing shelf for unsupported or unstable bundles.

2. Felt or EPDM separates a finished edge from hard steel
Edge chips often start at a concentrated hard contact point: a burr, exposed steel, dirt trapped at the base, or a lining that has shifted. A felt-lined stone contact surface creates a softer separation between the slab edge and the rack. Where the project calls for an EPDM protective profile, it can be specified as the contact interface for the applicable configuration. The 15742 stone / 4 × 8 ft reference does not assume a rubber strip; it is a felt-lined stone direction. Inspect the lining before each loading cycle and replace worn or contaminated material rather than loading a slab onto exposed metal.

How the counterweight resists forward tipping
The L-frame places the slab load against the rear support while the extended base and counterweight create a wider stability footprint. This manages the forward tipping moment; it does not remove the need for a level, suitable floor or correct loading. Keep the slab mass within the selected model rating, load from the approved side, distribute the bundle as designed, and use site restraints or anchoring when the risk assessment requires them.
Why hot-dip galvanizing matters outdoors
Muddy yards, standing water, washdown, and repeated outdoor exposure attack an ordinary painted surface more aggressively than a clean indoor floor. Hot-dip galvanizing is available when the project needs added corrosion protection; it is optional, not the default finish. Powder coating remains a separate finish choice for suitable environments. Tell us about mud, drainage, cleaning chemicals, and storage duration so the surface treatment is selected deliberately.
Plan a stone slab rack around your real inventory
Send your largest granite or marble slab size, 4 × 8 ft quantity if applicable, maximum bundle tonnage, forklift or crane details, indoor/outdoor condition, and preferred rack count. We will use those inputs to review the upright layout, felt or EPDM contact option, counterweight/base arrangement, and optional hot-dip galvanizing. For broader glass storage, transport, and return-rack requirements, ask about the related Grack configurations and applications.