WhatsApp Telegram
CONTACT
GSR Hrack Technical Solution · Thin-board warehouse layout

The client needed one rack family for a mixed inventory that runs from 2 mm to 25 mm, while the thin-board zone still had to stay calm, visible, and easy to reach.

The practical answer is simple: use Hrack for the thin boards, keep the wall rows tight, and place a back-to-back block in the middle so the room still has a clean traffic line after the first layout is installed.

1700 mm × 1900 mm
Maximum board size in the brief
650 mm × 1350 mm
Minimum board size in the brief
14 mm / 12 mm
Net slot width and maximum stored thickness
42 racks
Wall rows plus back-to-back middle block

Technical drawing of a Hrack frame sized 1500 mm by 1000 mm for boards up to 1700 mm high and 1900 mm long

What the client was trying to fix

The inventory is not a single thickness band. The brief covers 2 mm, 3 mm, 4 mm, 5 mm, 6 mm, 8 mm, 10 mm, 12 mm, 14 mm, 16 mm, 18 mm, 20 mm, and 25 mm sheets. That kind of spread is exactly where a loose warehouse layout starts wasting space and letting the thin boards move when operators need fast access.

The rack plan therefore has to do two jobs at once: hold the thin boards in a controlled line and keep the room usable after the first rack row is in place. If the aisle gets swallowed by the layout, the storage room becomes harder to work than the glass itself.

Structural specification

Project number14823
ProductHrack
Board size, maximum1700 mm (H) × 1900 mm (L)
Board size, minimum650 mm (H) × 1350 mm (L)
2 mm boardsAbout 200 sheets
3 mm boardsAbout 250 sheets
4 mm boardsAbout 250 sheets
5 mm and 6 mm boardsAbout 360 sheets in total
8 mm and 10 mm boardsAbout 300 sheets in total
12 mm, 14 mm and 16 mm boardsAbout 360 sheets in total
18 mm, 20 mm and 25 mm boardsAbout 160 sheets in total
Rack structureAssembly type, bolt-connected
Storage width per slot14 mm net storage width
Maximum stored thickness12 mm

Warehouse staging view of wrapped Hrack racks used for mixed-thickness glass board storage

Layout logic for the warehouse

The thin-board zone should stay with Hrack first. For this project, that means the 2 mm to 10 mm band gets the tightest control, because those sheets move often and need the cleanest separation. The 14 mm net slot width fits that job, and the 12 mm thickness ceiling gives the rack family a clear operating limit.

For the room layout, place racks along both walls, then set a back-to-back block in the middle. In the project notes, that arrangement can hold 42 racks and still leave usable clearance after the main rows are in place. If the client needs more capacity later, the remaining space can take extra racks or another work zone without reworking the full room plan.

Hrack handling path beside the rack line in a warehouse staging area

Engineering notes that matter on site

The rack family uses Q235A carbon steel for the main frame, with PVC or PVB sleeved separating lines and a powder coated finish after surface prep. Those are not decorative details. They keep the frame stable while keeping hard metal contact away from the glass edges.

The operating logic is the same from loading to retrieval: keep contact points controlled, keep the backrest cushioned, and keep the frame behavior predictable when the load sits still. That is what the product line is meant to do in a real workshop, not just in a catalog view.

Packing and risk points

The project allows stretch film plus strapping, or ratchet strap packing after stacking. That is a basic transport method and it does not protect against impact damage during transit, so light scuffing and paint marks can still happen. If the client wants a harder packaging standard, a wooden crate is possible, but it adds cost and reduces loading quantity.

  • Forklift entry must stay smooth and even. Sudden fork movement can bend the base and disturb the frame.
  • The base, uprights, and weld points need scheduled checks for bending, deformation, and open welds.
  • When racks are stacked, the upper feet must sit fully on the lower uprights before the lower unit is released.

What to confirm before release

Once the room drawing, the rack count by zone, and the exact thickness split are fixed, the layout can be locked without guessing. That is the point where the plan stops being a rough idea and becomes a build list.

Send the warehouse plan and sheet breakdown to lock the rack count and layout.

Email
get a quote
whatsapp