WhatsApp Telegram
CONTACT
DOUBLE-SIDED A-FRAME PANEL STORAGE TROLLEY

Double-Sided A-Frame Granite Slab Rack for Stone Fabrication Yards

Keep 2000 × 600 mm granite slabs supported from the center instead of leaning them against a wall. This Mgrack project configuration uses symmetric double-sided A-frame support, C-channel steel with profile rubber strips, an 8 mm base plate, and forklift-ready handling interfaces. The figures below are tied to project 14629, not universal Mgrack ratings.

Send slab size and weight
Double-sided A-frame glass storage rack with swivel casters and lifting lugs for panel turnover

A controlled storage position for heavy stone slabs

For stone fabrication yards and granite distributors, the operating question is not simply whether a rack can hold a panel. It is whether the slab can be loaded, restrained, moved and returned without relying on a wall, bare steel contact or a permanently welded frame. Mgrack is a knock-down, mobile double-sided A-frame panel storage trolley. In the 14629 stone-rack configuration, the rack was specified around 2150 × 600 × 800 mm slabs of about 2000 × 600 mm, with one side using 180 mm of storage width. Confirm your maximum slab envelope and unit weight before quotation.

PROJECT CONFIGURATION · 14629

The numbers for the granite slab version

Use this table as a project reference for the stone-rack configuration. It must not be read as a standard load rating, standard footprint or standard container count for every Mgrack variant.

Swipe or scroll on mobile to view the full specification
Item14629 project valueWhat to confirm before quoting
ApplicationGranite slab storage and internal turnoverSlab material, maximum size, thickness and edge condition
Rack dimensions2150 × 600 × 800 mmActual slab envelope and aisle/vehicle clearances
Project load1 tonnePer-unit weight, distribution, static or moving use; engineering review required
Single-side usable width180 mmWhether the required slab stack fits within the selected side width
Base reinforcement8 mm steel plate along the 2150 mm direction, both sidesContact arrangement and local protection required for the slab
Contact protectionC-channel steel with profile rubber stripRubber type, replacement plan and protection at every contact point
Approximate rack weight117 ± 3 kg without rubber; 125 ± 3 kg with rubberFinal drawing, accessory package and weighing basis
Handling interfacesForklift entry along the long side; caster or lifting options depend on configurationFork dimensions, center distance, turning space and whether overhead lifting is required
FinishElectrostatic powder coatingColor, surface expectation and packaging protection
Container reference20GP: 60 sets; 40HQ: 144 sets14629 project packing basis only; wooden crates can reduce quantity
Close-up of galvanized ratchet buckle and blue webbing on powder-coated A-frame rack for glass transport

Choose the handling path before choosing the rack

The 14629 design is for long-side forklift entry. A mobile rack may also be configured for caster movement, while lifting lugs are a separate handling interface that must be reviewed for the actual rack, load and lifting method. Do not assume a visible eyelet proves a rated overhead lift.

  • Send maximum slab length, width, thickness and single-piece weight.
  • Tell us whether the rack is pushed, forked, lifted, or used in combination.
  • Confirm aisle width, fork dimensions and surface-protection expectations.
Request a configuration review
HOW THE RACK WORKS

Three control points for stone-fabrication turnover

The value is in the operating sequence: support the slab from both sides, isolate the contact surfaces, restrain the load, then move the rack with the interface matched to the shop floor.

Symmetric A-frame support keeps the load centered

A double-sided A-frame gives the slab two opposing storage faces instead of a single wall lean. The centerline support helps keep the loaded mass within the rack footprint while the base plate receives the lower reaction. In practice, the operator still has to load evenly, use the specified restraints and move at a controlled speed. The 1-ton figure belongs to the 14629 granite-slab project configuration only; it is not a universal Mgrack capacity.

Close-up of steel-embedded rubber pads on a powder-coated A-frame panel storage rack

C-channel steel and profile rubber separate stone from steel

The project specification uses C-channel steel with profile rubber strips at the contact area, plus an 8 mm steel plate along the long base direction to receive the heavy load. The rubber interface is intended to prevent direct hard contact and reduce scratching or impact at the support line; it does not remove the need to check slab edges, debris, loading method and replacement wear parts. A limit bar and ratchet tie-down can be selected to hold the slabs against the frame during turnover.

Forklift loading a double-sided powder-coated steel glass A-frame rack with swivel casters in warehouse

Forklift or overhead handling?

For the 14629 stone version, long-side double-sided forklift entry is specified. If your yard uses a crane, request a lifting-interface review instead of treating lifting lugs as a blanket rated claim. Provide fork size, center distance, lifting equipment and the loaded rack weight.

Empty-rack return and packing

The KD layout separates the base, four triangular frames and two connecting beams for dense empty-rack packing. The 14629 reference is 60 sets in a 20GP and 144 sets in a 40HQ. Stretch film, straps and ratchet bands are economical but may allow light paint scuffing in transit; wooden crates offer added protection while taking more space and reducing quantity.

Worried about slabs tipping or edge damage?

Send your maximum slab size, single-piece weight, number of slabs per side, preferred handling method, fork dimensions and packaging requirement. We will review whether the 14629-style 2150 × 600 × 800 mm configuration fits, or specify a double-sided A-frame around your stone dimensions.

Get a slab-specific A-frame proposal
Email
get a quote
whatsapp