Coated glass handling · contact faces · double-sided A-frame glass rack
A Low-E or magnetron-sputtered coating is a metal-oxide film a few tens of nanometres thick sitting on the glass surface, and there is no repair path once it is cut. One rub against bare steel in a glass fabrication workshop takes the film off in a line, and a pane that was sellable stock becomes scrap. A rubber padded glass rack works on the cause: on our double-sided A-frame glass rack every glass contact face carries either 10 mm flat rubber or an embedded 44 × 10 × 26 mm C-channel rubber strip, so Q235A carbon steel stays out of the contact path, while a limit rod and a ratchet tie-down press the pack onto the pads at a 90° ±2° lean.
Between the cutting table and the insulating line, coated stock spends most of its life standing on something. Off the coater it goes onto an A-frame, off the A-frame onto a trolley, off the trolley into a stillage for the lorry. Every one of those transfers is a chance for the coated face to meet a harder material with grit trapped in between, and the film does not forgive it.
The awkward part is that this loss is not a machine problem. The cutter, the edger and the washer do their work in a controlled envelope. The rack is the only asset in the flow that is bought once, priced like a consumable and then asked to protect a panel worth several thousand dollars on its own. So the question worth asking before the next order is not how heavy the rack is, but what actually touches the coating, and how that contact is held in place while the rack is being pushed, braked and forked.
The failure sits at the contact patch, not at the load
Sputtered Low-E films are thin oxide layers on top of the glass, not inside it. They mark from abrasion at low pressure, and grit is the multiplier: a grain of blasting media on a steel rail will score a line through the film long before the glass itself shows anything. The usual arrangements in a workshop keep supplying that grain. A timber A-frame arrives with nails, knots and sawdust, drinks coolant and holds it against the pane edge. A bare steel tube rack has nothing between the tube and the glass except a strip of self-adhesive foam, which creeps under load, swells with water-based coolant and eventually peels back to expose the tube underneath. Once the pane is standing naked against steel, every wheel caster bump and every brake application transfers into a small sliding motion at the bottom edge, exactly where the film is easiest to break.
Fixing that means taking steel out of the contact path as a property of the structure rather than as an accessory taped on afterwards. On this double-sided A-frame glass rack the protection is part of the frame: pads and strips are fixed to the profiles at build stage, inspected with the frame, and replaced as a component rather than re-glued as a patch. The rack is also built to be moved loaded, which is a different brief from a static storage frame — hence the casters, the fork pockets and the lifting points, and hence the restraint that keeps the pack from shifting when the rack is moved.

What the contact faces and the frame are made of
Take a documented build from our files, not a catalogue headline. The frame is Q235A carbon structural steel: base tube 60 × 3 mm, A-frame uprights in C-channel 50 × 25 × 2 mm, cross beams in 8# channel at 80 × 43 × 5 mm. Individual parts are fully welded, then the frame itself bolts together so it can ship knocked down and be assembled on site. Both faces carry the same pad arrangement, because a double-sided rack that protects one side and not the other simply moves the scrap to the other face.
On the glass side there are two contact options. The first is a 10 mm flat rubber pad, used where the pane presents a broad face to the frame. The second is the 44 × 10 × 26 mm C-channel rubber strip, a profile that seats inside a formed steel channel along the load face, so the pane edge meets a rubber section rather than the tube it is mounted on. Both are held by countersunk screws through the strip and its steel backing instead of adhesive, which matters when the strip is wiped down with coolant every week. The A geometry holds the pack at 90° ±2°, set in the jig at build, not adjusted in the aisle: the lean is what keeps pane weight in compression against the pads instead of hanging on the straps.
The rest of the build follows the handling method. Casters are commonly 6-inch iron-core polyurethane, two braked swivel plus two fixed, with 5-inch, 8-inch and six-wheel sets available where the pack is heavier or the aisle is tighter; quick-release pin wheels exist for shops that want the wheels off during static storage. Fork entry on documented builds runs a 164 × 92 mm pocket with 500 mm centre distance at the front and 600 mm at the side, and lifting eyelets are fitted only where the buyer confirms the rack will be lifted, because an eyelet on a frame nobody slings is a false assurance. Recorded load configurations in our files run from 1000 kg to 3000 kg evenly distributed, which is a record of past builds, not a series rating; the frame and pad layout are confirmed against your own panel list before quoting.
The limit rod and the ratchet tie-down keep the pane on the pad
A padded face only protects while the glass stays against it. The two parts that do that job are deliberately simple. A limit rod across the outer face gives the pack a steel reaction point, so the stack cannot lean out past the frame envelope. A ratchet tie-down then pulls the stack back into the pads: webbing over the top beam, a galvanised buckle taking up the slack, tension set by hand until the outermost pane is seated. The strap path matters as much as the tension — running the webbing over a top beam or guard keeps it off the coated faces, so the only thing pressing on the glass is rubber.

With both in place the pack becomes one body with the frame. A braked caster on a concrete joint, a forklift setting the rack down slightly off level, a turn in a narrow bay — the pane no longer rocks half an inch and slides back. That is the whole result: the contact patch stops moving, so the coated face is not being rubbed by anything, and the defect that used to appear at final inspection stops being generated at the rack. Shops running coated stock usually find the payback in re-inspection time before they find it in scrap value, because a pane that has to be pulled, checked under a light and re-labelled costs labour whether or not it is finally rejected.
Four things to send before we quote a coated-glass rack
- Panel build and which face must stay untouched. Length, width, thickness and the coated side decide whether the pane sits on a 10 mm flat rubber pad or on the 44 × 10 × 26 mm C-channel strip, and whether the pads should touch the bottom edge only instead of the coated face.
- Unit weight and panels per face. These set the usable side storage width and the frame height, which trade against each other — recorded side widths run from 180 mm to 420 mm, and a wider slot is paid for in height. We confirm the frame against your pack rather than picking a number off a list.
- How the rack will be moved. Hand push, forklift, or overhead lifting each change the build: caster set and brake arrangement for pushing, pocket depth and centre distance for forklift handling of glass panels, and eyelets only where lifting is confirmed.
- Floor, aisle and who re-torques the bolts. Brake casters and anti-tip legs set 30–50 mm off the ground belong to a floor and a turning radius, and a knocked-down frame is only as rigid as its assembly. Name the person who checks bolts, welds, uprights and wheel pins on a schedule, and the rack keeps the geometry it was built with.
