← Back to Insights

Rough-Back Natural Stone and the EN 13155 Question: Where an H-Type Glass Vacuum Lifter Seals and Where It Needs a Trial

2026年10月15日 | By | In Blog
Eight-cup vacuum glass lifter with yellow steel frame and central lifting mast

Stone & glass handling · vacuum lifter selection

A fabricator quoting polished quartz and rough-sawn natural stone in the same order hits the same two walls on every vacuum lifter quote: a flat 300 mm silica gel suction cup needs a continuous contact patch to seal, and an EU site buyer now expects CE / EN 13155 paperwork and a dual vacuum circuit. This is where an H-type glass vacuum lifter seals cleanly — glass, polished marble, quartz, sintered stone, ceramic — where a rough uncalibrated stone back needs an on-site seal trial and pad-layout work instead of a promise, and how we talk honestly about the certification roadmap for the single vacuum circuit we build today.

A stone and glass fabricator rarely gets a clean single-material order any more. The same week can bring thirty polished quartz blanks for a kitchen programme, a run of 3 mm ceramic sheets, and one architectural job in rough-sawn granite where the visible face is honed but the back is exactly as it left the gang saw — textured, uneven, and holding a layer of stone dust that was never calibrated off.

On paper, one electric glass suction cup lifter should cover all of it. In practice the old handling sheet for that mixed order is a three-person carry between the rack and the saw table, a sling and strap arrangement for anything over a certain size, and a handheld vacuum cup used one operator at a time for the lighter blanks. None of those three give you a documented hold time, a rotation, or a number you can hand to a customer’s safety officer.

Where the old plan breaks on a mixed stone and glass order

The sling and strap method still works, but only on loads with an edge the sling can cradle. A polished quartz blank and a 3 mm ceramic sheet have the same problem: there is no edge you can wrap without concentrating force on the one face the customer will inspect. A handheld vacuum cup solves the edge problem and creates a new one, because the operator is standing under the load and every extra re-grip is another chance to mark a honed face.

Re-gripping is the quiet cost. A slab that has to be picked, set down, turned and picked again spends four contact cycles on the same surface instead of one. On book-matched pairs and veined material the mark is not always made by the lift — it is made by how many times the slab is touched, and by the fact that a strap or a hand cup cannot present the panel to the install face at the angle the job needs.

Modular H-type glass vacuum lifter with 8-pad layout, central control cabinet, vacuum pressure gauge and rotating mechanism

Why a flat silica gel cup seals on calibrated faces and not on a rough back

A vacuum suction pad does not hold a panel by gripping it. It holds it by pulling a thin volume of air out of the gap between the pad lip and the surface, so the atmosphere does the work. That only happens when the lip has a continuous contact line.

On glass, polished marble, ceramic, quartz and sintered stone, the face is flat enough that a 300 mm silica gel suction cup at roughly 100 kg per cup seats in one pass. On a rough, uncalibrated natural stone back, the same flat pad seats on the high points and bridges the rest, so we treat it as an engineering assessment rather than a catalogue claim. What we offer there is a pre-sale seal trial with a real slab plus pad-layout optimisation: moving the pads onto the flattest zones using the pin-hole positions in the frame, and, where the slab is heavy, adding pads so the load is divided across more contact patches instead of fewer. If the back is too open for a flat pad, that comes back as a no — and a different handling method.

The same honesty applies to curve. A panel with one curved edge is not proof that a standard flat pad covers every curved surface, and we do not write it that way.

What the vacuum gauge and the two-hour hold actually cover

On the machine itself, the lifting criterion is visible before the hook takes any weight: the pads must be seated and the vacuum must sit stable inside the −60 to −80 kPa window. A Thomas vacuum pump pulls the circuit through a non-return valve, a Panasonic digital vacuum pressure switch watches the level, and an audio-visual alarm calls out any drift. The vacuum gauge and the battery gauge are both on the console, which is what stops a shift from starting on an assumed seal.

If the site loses power mid-lift, the circuit holds the load for at least two hours on the DC24V battery and the non-return valve. That is the number to plan the day around, not a five-minute bridge. Capacity is 800 kg on the GL-SC-800H with 8 pads, or 1200 kg on the GL-SC-1200H, which extends to 12–24 pads on the single-side 800–1500 mm extension bar so a long slab keeps pad coverage right out to its ends. Rotation and tilt are electric and run off the wired remote handle, so one operator can pick the slab from the rack, turn it to the install angle and set it once.

What to settle before you specify — and what this lifter answers

  • Face condition, measured or assumed? Tell us the actual face. Calibrated and polished stone, glass, ceramic, quartz and sintered stone seal on the flat silicone pad. A rough uncalibrated back goes to the free trial-and-layout step described above, and we only offer a configuration after that trial, not before it.
  • Load per contact patch. Our 300 mm silica gel cups are rated at about 100 kg each. The 800H runs 8 pads; the 1200H extends to 12–24 pads with the extension bar, so a 1.2 t slab is divided across more patches rather than concentrated on a few.
  • Power loss on site. The non-return valve and DC24V battery keep the vacuum for at least two hours after a power cut, with the pressure switch and alarm watching the whole time — this is the fall-protection layer we already build in.
  • Certification route. Current machines use a single vacuum circuit, and we do not hold a CE / EN 13155 certificate to hand over today. We will not print one on a datasheet either. What we can give you is the current build status in writing, the sealed component cover, the non-return valve and alarm stack that make up the existing safety layer, and the certification work as a roadmap item on the model you are quoting.

Send us the slab list — material, face finish, thickness and the heaviest panel — and we will tell you whether the 800 kg or 1200 kg H-type glass vacuum lifter fits, how the pads should be laid out, and whether your rough-back stone needs a seal trial before we quote.

Talk to our handling engineers

Request a Factory-Direct Price Quote

Get customized CAD drawings, dynamic loading calculations, and wholesale price quotes. Response within 12 hours.