Glass fabrication workshop · switchable PDLC laminates · vertical panel storage
A switchable PDLC panel carries a liquid crystal film, two transparent conductive layers, edge busbars and a moisture seal between two glass sheets, so a hard clamp or a vibrating deck scraps the electronics long before the glass breaks. How a mobile glass storage rack with casters keeps pressure off that stack: 44 x 10 x 26 mm arc rubber strip seated in a C-channel, flat rubber of about 10 mm, steel-embedded composite pads, a rubber-faced limit press rod that sets the gap and a ratchet tie-down that pulls on the top beam instead of the panel edge. Pad type, cradle angle, caster set and load figure are confirmed on your panel list per order, not published as a series standard.
A switchable PDLC panel leaves lamination as an electronic part, not a sheet of glass. Two substrates, a liquid crystal film between them, a transparent conductive layer on each inner face, busbars along the edges to carry the drive voltage, and an edge seal that has to keep moisture out for years. In a glass fabrication workshop those panels move from lamination to edge trimming to packing on an A-frame panel storage trolley: held in vertical panel storage, pushed by hand, forked, or slung. Internal material handling is where the value is either protected or lost.
The rack most shops start with is a timber A-frame, a blanket over the timber, two foam blocks under the pack and one strap over the top. Over four hundred kilometres of road the foam takes a compression set while the strap keeps its tension, the pack settles, the sheets shuffle against each other, and the strap bears on the top edge — which is exactly where the busbar sits. Nothing looks broken at the gate. The panel fails at the drive test, and a delaminated switchable pane has no repair path.
Where the panel actually dies: a contact line, not a load figure
Pressure is force divided by area, and the area is where a rack either works or ruins the load. A foam block under a 300 kg pack gives a contact patch the size of a hand; a bare steel channel edge gives a line. A dimming laminate has a film stack and an edge seal that will not take a line load: the seal absorbs the shear, a moisture path opens, and the electrode at that edge is the first component to go. Transport vibration finishes the job, because a strap that was tight at the dock is slack forty kilometres later and a slack pack moves. So the useful question about a double-sided A-frame glass rack is not how many tonnes it holds, but what touches the glass and over how much area.

Three contact layers on a Q235A frame
On this build the contact path is rubber, in three forms. Base beams, triangular supports and the limit rod carry a 44 x 10 x 26 mm arc profile strip seated in a C-channel; the arc seats the panel edge so the strip bears on a band instead of a point, and the C-channel holds the strip against sideways creep. Where a sheet face meets the frame, a flat rubber sheet of about 10 mm takes the load. At the positions that see the highest unit pressure, a composite pad with an embedded steel plate keeps the rubber in shape instead of letting it extrude out of the gap. The frame itself is Q235A: base profile 60 x 3, A-frame upright in 50 x 25 x 2 C-channel, 8# channel beam at 80 x 43 x 5, parts fully welded and bolted to each other rather than welded into one piece. Both sides are symmetric on a 90 degree cradle, so a pack cannot bias the frame to one face.
Limit press rod plus ratchet tie-down: closing the pack without pinching it
Closing the pack is where most damage is made. A single strap over the top pulls the pack forward into the frame corner, so crews over-tighten to stop the shuffle and convert that into a point load on the top edge. Here the rubber-faced limit press rod sets the gap first: it pushes the pack back against the frame and holds the stack from tipping forward, and only then does the ratchet tie-down pull the load closed. The webbing runs across the top beam, so tension goes into steel and the rod, not into the panel edge, carries the closing force. The result is a pack that cannot slide layer against layer on a washboard road, on a rack that is also a polyurethane caster rack when the route is internal: 6 inch iron-core wheels, two swivel with brake and two fixed, or a quick-release square-tube and pin set when the wheels have to come off for a container. Fork pockets measure 164 x 92 mm inside, 500 mm on the front centre and 600 mm on the side, with anti-tip legs standing 30 to 50 mm off the floor. Lifting eyelets belong to the models specified with them, not to every frame. Fork in level and slow, and keep bolts, welds, uprights, caster pins and legs on a checking schedule.

What to send before we cut steel
- The panel list: maximum and minimum length, width and thickness, the unit weight, and the total weight you intend to stand on one side. Frame length, cradle angle and the one-side storage width — recorded between 180 and 420 mm on past builds — are set from those numbers, and the load figure stays a record for your drawing rather than a series standard.
- Where the busbar and the edge seal sit on the panel edge. That position decides whether the contact is an arc strip in a C-channel, a flat rubber sheet or a steel-embedded composite pad, and how wide the bearing band has to be. We line the band the seal actually needs instead of adding pad thickness until the noise stops.
- How the rack is moved: by hand, by forklift, or by crane. Fork pocket size, two-way or four-way entry, caster size and the quick-release pin set are separate decisions, and so are lifting eyelets. A glass and stone handling rack can be built for any of the three, but not all three on one frame without saying so before the drawing is issued.
- What happens to the frame after unloading. A nested and stackable return rack only pays when it is planned: bases, triangular supports and beams are bolted, so they separate and stack flat, with 11 bases to a stack on a 2400 x 1030 x 2050 build and container counts of 28 to 60 sets in a 20GP and 40 to 180 sets in a 40HQ — each confirmed by a loading simulation on your sheet pack, never quoted from the catalogue.
