Harp rack · glass harp rack · shop floor transfer
A 1,800 x 2,000 mm lite of 12 mm glass weighs roughly 108 kg, and in most glass shops it still leaves the cutting table on two pairs of hands. A heavy duty glass transport rack changes the class of control rather than the technique: the sheet goes into a numbered slot, the mass moves onto 5 in. or 8 in. polyurethane casters, and a foot-operated floor lock takes it back off the wheels at the station. That is how a glass harp rack helps minimize manual handling without slowing the shift down.
A wholesale fabricator running high-mix, non-standard orders does not move a pack once. Between cutting, edging, washing, tempering and IGU assembly, the same sheet is picked up, tilted, walked twenty metres and set down again a dozen times a shift, and every one of those events is a manual handling event. A 1,800 x 2,000 mm 6 mm lite is about 54 kg. The same sheet in 12 mm is about 108 kg. Neither number changes because the shop is careful.
The old layout accepts that cost. The A-frames and L-frames stand against the wall because that is where there is room, so the sheet comes off the cutting table onto hands, gets carried to the machine, and is stood up against or laid on whatever is free. Two workers on one sheet is an administrative control, not an engineering one: the load still hangs off fingers hooked over an arris, the shorter worker takes more of it, and the set-down onto a floor with grinding slurry is the moment that ends in a report. Casters on the right rack move that exposure from the body to the machine, and the rest of this piece is about what the rack has to get right for that to be true.
Ergonomics Begins at the Caster, Not at the Glove
The ergonomic decision on a harp rack is made below the frame. On the recorded builds the frame is Q235A carbon steel square tube, industrial full-seam welded at main nodes on the heavy models, with bolted joints where the unit has to travel flat. The bottom line is either a nylon roller shaft or a full steel slotted base carrying an HDPE slotted board, and underneath it sits the caster set: 5 in. or 8 in. heavy-duty polyurethane or nylon wheels, standard arrangement two fixed and two swivel with brake, and on project 15198 the fixed pair was specified on the stop-rod side with the swivel pair at the front roller side. That layout is not cosmetic. Fixed wheels on the pull side and swivel on the entry side mean the unit is steered from behind the load instead of dragged sideways, which is the difference between a shoulder pull and a push with two hands on the frame.
The size of the wheel does the rest of the work. A 1500 x 1200 x 1805 mm build was drawn on 8 in. casters with 1,614 mm of clear storage height; a 1310 x 600 x 1220 mm build carries 60 slots at 14.3 mm slot width on 5 in. wheels. The small unit suits a tight aisle between two machines, the tall one suits a route with expansion joints, drains and a slab step at the door, where a small hard wheel stops and a larger one rolls through. The same base carries the slot numbering — 01 to 23, 05 to 18 or 57 to 74 on high-density builds — so a worker goes to an address instead of sorting through a pack, and the hands are on the sheet for the length of one insertion rather than for a search.

What a Caster Load Changes, Sheet After Sheet
Load figures on this family belong to projects, not to a catalogue. A 60-slot 4 mm build in Romania was drawn at 300 kg; regular models are quoted around 800 kg; the standard heavy builds and their acceptance records sit at 1,500 kg; large custom frames go past 2,500 kg. The case that matters for manual handling is the last one. A nested rack in a record project holds four 650 x 2400 x 1900 mm harp units, 25 sheets each, 100 sheets in total, and 25 sheets of 1,800 x 2,000 x 12 mm is about 2,500 kg. Full, that unit is not something two workers steer across a shop; the push force has to be worked out before the loaded rack is allowed into the aisle, and on that scale the loaded unit goes on a forklift down a reserved route while the frame is pushed only empty.
Where the rack is pushed loaded, what the body meets is a horizontal force at waist height, with both hands on the frame, the feet under the hips and the route ahead visible. That is a different demand from a lift and a twist, and it is the reason the casters are specified against the floor rather than against the price list. Slurry, paint overspray, grit and a worn tread all raise the force needed, and plants do report casters as their fastest-wearing part on this equipment. Treat the wheel as a consumable and pick the compound for the surface the rack lives on. The honest limit is equally simple: casters do not make a 2.5 tonne pack a one-person job on a slope. They remove the carry, not the mass.
The Lock Is the Half of the System That Stops the Load
A caster brake holds by friction between tread and floor, and an edge grinding line removes exactly that. Water, rust inhibitor and cutting oil reach the concrete, the braked wheel slides, and a loaded rack walks until it meets a floor joint. The foot-operated locking mechanism on this rack is a different class of restraint: the pedal drives a lever past over-centre and lifts the base onto fixed rubber blocks, so the mass no longer stands on four wheels and there is no friction pair left for oil to spoil. Some builds carry two plunger locks under the base for the same reason a long frame gets two stations, and the number of lock stations is set on the order drawing against the frame length.
With the frame stopped, the pack itself is what keeps the sheet from going over: a wide EPDM rubber strip bolted across the sloping backrest instead of glued, vertical PVC-sleeved steel wire dividers that give every lite its own bay, and a slot width cut to the thickness being run — 8 to 10 mm on 6 mm work, with 12, 14, 14.3 and 25 mm recorded on other projects. A sheet that stands in a slot cut to its own thickness does not swing when the frame is locked, and a sheet that does not swing can be inserted and withdrawn by one worker with both hands in the slot line instead of one hand on the arris. That is the practical content of an anti-tip lock: geometry and restraint doing the holding, not a worker’s grip.

Four Lines to Confirm Before the Base Is Bent
- Panel envelope, smallest as well as largest. Give both. Slot width follows the thickness band you actually run — 8 to 10 mm for 6 mm lites, and 12, 14, 14.3 or 25 mm where a project calls for it — and a frame drawn around your biggest sheet can still leave your smallest piece awkward to reach.
- Load per rack and the floor under it. The load figure is set per project, from 300 kg on the 60-slot 4 mm build to 1,500 kg on standard heavy models and past 2,500 kg on large custom frames. It decides the caster size and compound: 8 in. polyurethane for a route with joints and thresholds, 5 in. where the aisle is tight, and a heavier tread where the floor carries grit.
- Lock stations and the side the operator stands on. One foot-operated lock on a short base, two plungers on a long one, positioned so the pedal is reachable where the worker actually loads. The caster split goes with it: fixed pair to the stop-rod side, swivel pair to the loading end.
- The route, measured, not remembered. Aisle width, slope, door thresholds and the number of transfers per shift decide whether one large rack or two smaller ones keeps the push inside a safe range, and whether the loaded unit is pushed at all or travels on a forklift through a closed fork channel.
