Glass harp rack engineering — jumbo lites and multi-tonne packs
A 3.6 m by 20 m rib of laminated or bullet-resistant glass leaves the line weighing tonnes and overhangs both ends of whatever trolley it lands on. On a light stitch-welded frame that overhang becomes a fatigue load: the base twists, the pack plane rotates on each push, and the caster brake is the only thing holding a multi-tonne panel still. This is how a heavy duty glass harp rack in Q235A carbon steel, with a foot-operated dead lock under the base, is drawn around the lite instead of the lite being forced onto the rack.
A 20 m rib is not a larger version of a 6 mm lite. It arrives at the shop floor as one panel weighing tonnes, it has to be pushed 40 or 60 m to the next process, and the frame carrying it is standing on four small wheels. Every push is a horizontal acceleration applied at hand height, while the mass sits on a bottom edge and overhangs the trolley at both ends. The load path is short and the lever is long, which is the opposite of what a general-purpose workshop trolley was drawn for.
Most mobile harp racks in service are built like furniture: thin-wall square tube, stitch welds at the caster feet, a slot grid sized for 8 mm to 12 mm architectural glass, and a wheel brake. That is a correct machine for cutting output. Put a jumbo rib on it, or a pack of thick laminated units, and the frame is asked to do something it was never dimensioned for — and it usually answers with a slow crack rather than an immediate collapse.
Where a multi-tonne lite breaks a welded trolley
The first failure is the base. The bottom rails act as beams spanning between casters, and on a jumbo load the span carries far more bending than the tube wall was chosen for. A stitch weld at the caster foot concentrates that bending into a short run of weld metal, which then sees a reversing stress every time the trolley is started and stopped. The second failure is torsion: the two side frames are tied together only at the base and at the top grid, so a load standing outside the footprint twists the whole box, the slot line goes out of plumb, and the panel plane starts to walk on the rollers. The third is the lock, because a wheel brake is a friction device. Water, rust inhibitor and cutting oil from a grinding or washing line take friction away, and a multi-tonne pack then moves on its own casters with nothing but a flat spot to argue with.

The base is the beam and the corner is the hinge
On a heavy duty glass harp rack the frame is dimensioned around the lite, not around a catalogue size. Main frames are Q235A carbon steel square and rectangular tube, with full-seam welding at the main-frame nodes that carry the load into the base, so the bending is shared along a section instead of parked in one stitch. Where the rack has to ship flat, the corner is a bolt group rather than a weld: paired high-tensile fasteners with locknuts through the base rail and the upright, shown in the close-up above, which lets the joint be re-torqued on site and lets a 3.0 m high, 1.8 m wide build travel as a crate. Slot count on this family is a drawing line — builds on record run from 40 slots to 84 — and so is the load: 300, 800, 1,500, 2,500 and 3,500 kg appear across separate projects, each on its own frame, and they must never be read as one model with a slider.
Dead lock, not a brake: putting the load on rubber blocks
A foot-operated lift lock does a different job from a caster brake. Stepping the pedal drives the base up onto fixed rubber blocks and takes the casters off the floor, so the panel is held by a mechanical stop that cannot be defeated by slurry, and the frame no longer rocks on four wheel contacts while a rib is being loaded or unloaded. Combined with the slot line itself — nylon roller shafts or a full slotted base covered with HDPE, PVC or PVB-sleeved steel-core wire dividers at 8–10, 12, 14, 14.3 or 25 mm, and an EPDM backrest where the lite leans — the lock is what turns a moving trolley into a stationary support at the moment the glass is vertical and unguarded.

What to send before a jumbo harp rack is drawn
- Mass and centre of gravity of the pack, not the sheet. Frame section, slot count and caster size follow this figure; on this family the recorded range runs to 3,500 kg per project drawing, and every value stays with its own build.
- How far the lite overhangs the frame at each end. That overhang sets the base rail section and how many lock stations are needed, because the blocks and not the wheels have to resist the resulting moment.
- Bottom edge condition. Polished arris, coated face, or a laminated or bullet-resistant build with a soft interlayer changes the answer between a nylon roller line and a full slotted HDPE base, and sets slot width from 8 mm upward.
- Floor and push method. Screed flatness, slurry and how many people push decide between 5, 6, 8 or 10 inch polyurethane or nylon casters and where the foot pedal sits so it can be reached with the pack loaded.
