Mfence wire mesh pallet collar · custom sizing for a mixed-size parts loop
One plant can bag nuts and bolts in one aisle and ship hoods and engines from the next, and no single container profile covers both ends of that span. How a custom wire mesh pallet collar is sized from three load numbers instead of a catalogue: deck footprint, stack height and the smallest part across the load face, documented at 1100 x 1100 mm with a 1000 mm effective height.
Packaging engineering at a North American agricultural and construction equipment plant usually gets the part list as one spreadsheet, and it reads like two different factories. At the top sit bagged fasteners, washers and small brackets. At the bottom sit hoods, castings and engines. Between them are a few thousand part numbers that all leave the same dock, and every one of them is currently assigned a container chosen either by habit or by whatever bin size was cheapest the year the line was set up.
That is where the money leaks. A container sized for the largest part is 60 percent air for the smallest, and the trailer pays for the air. A container sized for the smallest part puts the hood in overhang, which is a load-securing problem before it is a packaging problem. Buying a separate rigid box for each end of the span solves the fit and creates a return leg full of empty steel.
Why a Single Container Profile Fails a Part Size Span
Three legacy answers show up in almost every plant that carries a wide part spectrum. The first is a nailed timber crate built to the part, which fits perfectly once and is then scrap. The second is a catalogue rigid bin, bought in whatever footprint the supplier stocks, so the small parts rattle in a bin designed for something four times their volume and the large parts overhang. The third is stretch wrap and strapping over a bare pallet, which contains nothing above deck level, so a stacked tier sits on the parts rather than on structure.
All three share the same blind spot: they treat the container as a catalogue item instead of a variable. A wire mesh pallet collar is not a catalogue item in that sense. It is a bottomless frame that clips onto the pallet already in service, which means the pallet supplies the base and the collar supplies only the side wall and the stack interface. That single design decision is what makes a size span affordable, because the expensive part of the unit, the deck, is already owned and already in the loop.
Three Numbers Come From the Load, Not From the Catalogue
The documented Mfence build is a useful worked example of the method even though it started from liquid. It uses an 1100 x 1100 x 150 mm plastic pallet carrying 20 kg plastic drums at roughly 250 x 230 x 480 mm, 16 drums per layer over two layers, with a 1000 mm effective storage height and 40 mm left over as divider allowance for the 960 mm of product. Read it as a sequence: the deck fixed the footprint, the two-layer stack fixed the effective height, and the drum diameter fixed the vertical spacing that keeps the load away from the wall.
The same sequence runs on a mixed part spectrum. Fasteners and small brackets are the reason mesh aperture and wire diameter are asked about first, because a 100 x 100 mm mesh on 4 mm wire, the documented specification, will pass small parts through the load face. For that end of the span the answer is a finer mesh or an internal liner panel, confirmed against the actual part, not assumed. Hoods and engines pull the other way: they need the footprint, the effective height and, above all, an access opening that lets a person reach the lower tier after the unit above is already stacked.

What the Steel Looks Like When It Is Built to Size
The frame in the documented build is 40 x 40 x 1.5 mm Q235 rectangular tube, with welded wire mesh panels clipped between corner posts, latch corners that allow a panel to come out without tools, inner and outer staggered double hinges, and stacking feet that locate the tier above rather than letting it slide. The door is a 400 mm half door sitting above a 600 mm bottom wall, so the lower band of the side wall stays solid where the load pushes hardest and the opening lands at working height. Unit weight is about 47 kg with the 1.5 mm tube and about 48 kg with the recorded single-tier optimisation, which is an honest difference between two schemes rather than one specification.
The pallet interface matters as much as the frame. The latest feedback on that project calls for a four-way fork entry pallet instead of a three-way stringer design, with limit blocks that guide the forks and stop them hitting the mesh, and that requirement is confirmed per project rather than assumed to be delivered. Finish is a project decision as well: cold galvanised, hot dip galvanised, electrostatic powder or paint, sized to the environment the unit actually lives in.

What to Fix Before You Ask for a Quotation
- Deck footprint. Measure the pallet, not the part. Euro 1200 x 800, an 1100 x 1100 build and a non-standard deck all get a different collar, and because the unit is bottomless the deck remains the base of the container.
- Smallest part across the load face. A 100 x 100 mm mesh on 4 mm wire is the documented specification; where the part is smaller, specify a finer mesh or a liner panel instead of discovering the gap at the dock.
- Access after stacking. The 400 mm half door over a 600 mm bottom wall is the opening that lets the lower tier be picked without unloading the tier above; latch corners let a whole panel come out when the part is heavy and awkward.
- The empty leg. The double fold brings the set to about 2300 x 1100 x 140 mm and lets it seat back over an 1100 x 1100 pallet, which only pays on a route the plant actually repeats. On a one-way lane, the fold is not the argument.
Two limits belong in the quotation conversation, not in a sales line. No rated load and no stack table are published for this family, so the documented two-unit stack is a case record rather than a safety class, and each project needs its own stack figure. Dimensions, mesh, wire, door position, finish, liner and fork entry are confirmed per order against the drawing.
