← Back to Insights

Stretch Wrap, Tape and Divider Boards: Cutting Palletising Labour with a Clip-On Wire Mesh Pallet Collar

2026年10月30日 | By | In Blog
3D render of a stackable galvanized steel pallet cage with mesh panels and blue pallet base

Warehouse operations · pallet containment · labour per load

On a 1100 × 1100 pallet of 20 kg drums — 16 per layer, two layers, 960 mm of load — the slow part is not the stacking. It is the film, the tape, the corner boards and the divider pushed in by hand, then the wait while the forklift stands off the load until the wrap is finished. A clip-on wire mesh pallet collar builds the side wall instead of wrapping it: bottomless mesh panels clip together on the pallet already in service, 1000 mm effective height, 100 × 100 mm mesh on 4 mm wire, a 40 × 40 × 1.5 mm Q235 tube frame, a 400 mm half door over a 600 mm bottom wall, stacking feet, fork-entry limit blocks on a four-way entry pallet, and a 2300 × 1100 × 140 mm flat fold — with the honest limits that no rated load or stack table is published, that fork entry and finish are confirmed per project, and that two stacked units is a documented case rather than a safety class.

Walk the end of a palletising lane and the clock splits in two. Tier one and tier two go down fast, because a drum is a drum. Then the load stops moving: film round the corners, two or three turns at the top, tape along the seams of the carton or the divider boards pushed down between layers. Only after that does the pallet truck or forklift take it away. The steel in the load never changed — the labour was added at the outside.

A wire mesh pallet collar moves that labour to a different place in the process. It is bottomless: the four mesh panels clip to each other and to the pallet that is already in your loop, and the pallet becomes a three-dimensional unit with a steel side wall that is dismantled and re-used instead of cut off and thrown away. The structural numbers are plain: 1000 mm effective height on a documented 1100 × 1100 build, 100 × 100 mm mesh on 4 mm wire, a 40 × 40 × 1.5 mm rectangular tube frame, a 400 mm half door above a 600 mm bottom wall, stacking feet and corner posts that locate the tier above, and a double fold down to about 2300 × 1100 × 140 mm for the empty return leg. What follows is where that changes the labour and the forklift cycle, and where it does not.

Counting the Labour Nobody Quotes

Stretch wrap looks free because it is bought by the roll. Per load it is not: film, tape, corner protectors and divider sheets are consumed on every single trip, and the wrap has to be applied by a person standing at the load rather than driving a truck. Two more costs are less obvious. First, a wrapped block is opaque — labels, layer counts and damage are inspected by cutting or peeling the film back. Second, film is tension, not structure. It holds nothing vertical above the second tier, it slips on a smooth drum wall, and it has to be cut away before anyone can reach into the load, so the wrapped unit is effectively sealed until it reaches the line.

The collar’s answer is to stop wrapping the load and start building the wall around it. On a four-way entry pallet, fork entry is a property of the pallet underneath, and the collar is built to leave that entry clear — the project feedback for the documented 1100 × 1100 × 150 build calls for a four-way entry pallet rather than a stringer (川字) base, with limit blocks at the entry so a fork cannot slide past the pocket and lift the collar frame by the mesh. That is a requirement recorded in the project file, not a claim that every delivered unit has shipped that way; it is checked at the drawing stage for each order.

3D render of wire mesh pallet collar corner posts, stacking plates and clip connection points

Assembly by Clip, Not by Carton and Tape

A one-way carton needs tape on every seam, an internal divider to stop the walls bowing, and a decision about what happens to the box after delivery. The collar needs a person and no tool: front, back and side panels clip to each other at the corner posts, the latch closes the corner, and the side wall is standing. Empty, the same panels separate into single pieces, which is what makes them stackable for storage and cheap to move back to the packing station. Finish is quoted per project — hot dip galvanized, galvanized, powder coated or painted — and the unit weight sits at about 47 to 48 kg depending on whether the 1.5 mm tube or the optimised tube option is used, so a panel set is a two-person lift, not a crane job.

On paper the collar is deliberately anchored to the load: 16 drums of roughly 250 × 230 × 480 mm per layer, two layers, 960 mm of goods inside a 1000 mm effective height, the spare 40 mm reserved for a divider sheet so the tiers do not bear directly on each other. Sixteen drums per layer is a packing pattern, not a load rating. What the collar does not publish is a cycle time or a labour saving in minutes, because panel count, pallet condition and the operator’s route decide that. Time it on your own panel set before you write the saving into a business case.

What the Forklift Actually Sees

Forklift flow is where the collar earns its place next to wrapping. A wrapped load has no locator on top, so the second tier is placed by eye. The collar has stacking feet and corner posts at the top rail that take the pallet above and sit it in position; the double hinge runs inside and outside in a staggered pattern so the corners of a loaded unit resist racking rather than spreading. Because the mesh is open, the driver and the checker can see the load while it is moving — drum count, a leaking bung, a shifted carton — without cutting anything open.

Access after stacking is handled by the door, not by unstacking: the 400 mm half door sits above a 600 mm bottom wall, so the lower tier can be picked through the opening while the wall below still holds the load footprint. And the empty leg is where film has no answer at all: a rigid wrapped block still occupies its full height on the way home, while the panels fold to roughly 2300 × 1100 × 140 mm and a second fold seats the set back over an 1100 × 1100 pallet. Two limits are worth writing on the quotation: two stacked collar units is the documented case from the project file, not a published stack rating, and the open mesh passes small parts — fine components need a finer mesh or a liner board agreed per project.

3D render of a pallet fence corner with stacking tabs, top tube frame and bottom clip feet

What to Fix Before You Drop the Stretch Wrap

  • Pallet footprint and entry type. Measure the deck, not the catalogue: the documented build is 1100 × 1100 × 150 mm, and a four-way entry pallet is specified so fork entry stays clear — a stringer base changes the lift geometry and has to be confirmed before production.
  • Load geometry per layer. Count the pattern and the height: 16 drums at about 250 × 230 × 480 mm, two layers, 960 mm total inside 1000 mm effective height. If your load is taller, the effective height is a project dimension, not a fixed number.
  • Access point after stacking. If the lower tier must be picked without unstacking, the 400 mm half door over the 600 mm bottom wall is the access plan; if pallet-truck access matters more than a door, say so, because the panel configuration changes.
  • Mesh size against the smallest part. 100 × 100 mm mesh on 4 mm wire is right for drums and cartons; it will pass small mouldings and spherical parts, so a finer mesh or an internal liner sheet has to be agreed at drawing stage.

Send the pallet footprint, the layer pattern and the fork entry you actually run — we will come back with a wire mesh pallet collar drawing in that geometry, the finish you specify, and the fold dimension for your empty leg, instead of a standard size that nearly fits.

Send your pallet and load drawing

Request a Factory-Direct Price Quote

Get customized CAD drawings, dynamic loading calculations, and wholesale price quotes. Response within 12 hours.