Glass and stone handling · caster failure on the shop floor
A loaded double-sided A-frame glass rack carries several tonnes on four small wheels, and the floor is the part of the route nobody specifies. When one caster takes a chip of granite or a spalled patch of concrete and collapses, the corner drops, a two-metre frame rotates about the remaining three wheels, and a loaded face goes where gravity points. This is how four anti-tip legs set 30–50 mm above the ground on a mobile glass and stone handling rack change that sequence, what the steel under the corner actually looks like, and where the design is honestly the wrong answer.
In a glass fabrication workshop the loaded pack never sits still. A double-sided A-frame glass rack is pushed from the cutting table to the edging line, parked, loaded on the second face, pushed again to dispatch — and along the way it rolls over granite grit, a spalled patch of concrete, a drain cover, a steel threshold strip. On many builds the whole mass of the pack rides on four small wheels, and nothing else touches the floor. That arrangement gets tested the day one of those wheels meets a 20 mm chip of stone at an angle.
The failure is quiet and then it is not. A polyurethane tyre tears, or the bracket lets go, and one corner of the frame loses its only support. A two-metre frame carrying a loaded face does not sit down gently: it rotates about the other three wheels and picks up lean, and lean measured at the top rail is several times the drop at the corner. What follows is stone and glass arriving at floor level with people working nearby. Four steel anti-tip legs, standing 30–50 mm clear of the ground at the base corners, are the answer to that one second in the sequence — not to the whole accident, but to the part where a dropped corner becomes a falling pack.
The Only Ground Interface Is a Consumable
Walk round most welded A-frame trolleys in a stone slab handling bay and the bill of ground contact is four casters. The frame is a weldment, the base is a rectangle of steel section, and the wheels are bolted to its corners through galvanised brackets. Casters are the parts most exposed to the worst of the floor: grit, swarf, wash-down water, ramps, kerbs, the lip of a container. They are also loaded hardest per unit area — recorded distributed figures on this product run 1000 to 3000 kg, so a 2500 kg build carries roughly 600 kg at one corner before any dynamic amplification from a bump, and the corner hidden under the inside of the loaded face is the hardest one to inspect. When that wheel goes, a frame with no secondary ground contact has no second line of defence. In that design the caster is not a wear item; it is the entire stability system.

A Steel Leg 30–50 mm Above the Concrete
The legs are short steel posts welded into the four corners of the base, cut so their feet hang 30–50 mm clear of the floor in normal service. That clearance is set against the caster envelope: the wheel sits under load and deflects, the frame rolls and steers, and the legs stay out of the way. If a caster collapses, the corner can only fall that 30–50 mm before steel meets concrete. The frame lands on the leg at the corner it just lost, the load path returns to the ground through the base section, and the rotation stops there instead of accelerating. In practice that is the difference between a rack that has to be unloaded where it stands and a rack on the floor with a tonne of granite across the aisle.
The alternative usually proposed is a bigger wheel or a higher-rated caster. Both help and both have limits: a larger wheel raises the deck and the push height and changes where the load sits against the cradle, while a caster rating is a catalogue number measured on a test surface — your slab is not a test surface. Where the legs genuinely do not work is ground they cannot stand on. The design assumes hard, relatively flat concrete: an internal bay, a dispatch lane, a finished slab. In an unpaved outdoor yard, grit and soil let a leg touch down during ordinary rolling, and then it digs in, drags, and catches on a rut or a slope; on that surface the leg turns into a handling hazard instead of a stop. If your rack spends part of the day on gravel, that belongs in the quotation conversation, not in the brochure.
Reading the Corner: Section, Bolts and Caster Set
The frame above the legs is what decides whether the stop holds. On current builds the base is formed from 60 × 3 mm rectangular tube, with some drawings using 60 × 60 × 3; A-frame uprights are 50 × 25 × 2 C-section, the top beam is 8# channel at 80 × 43 × 5, and the steel is Q235A carbon. Main-frame nodes are full-seam welded, while the components themselves stay bolted so the rack can be broken down for empty-rack return and storage. The wheel in the photo is an iron-core polyurethane swivel on a bolted galvanised bracket; the mainstream set is 6-inch, two swivel with brake and two fixed, with a quick-release pin version for shops that pull wheels off before stacking. Above the base sit a fork channel of roughly 164 × 92 mm internal with front centres recorded at 500 mm and side centres at 600 mm, top lifting eyelets, a rubber-faced limit press rod and a ratchet tie-down across the top beam, plus 44 × 10 × 26 mm arc rubber seated in a C-channel and about 10 mm flat rubber on the contact faces. The legs sit in that same base geometry, at the corners, outboard of the caster brackets.

What to Settle Before You Specify One
Four things decide whether an anti-tip leg is protection or decoration, and each one lands on a different part of the drawing:
- Floor. A hard, flat internal slab is what the 30–50 mm clearance is drawn for. A rack that also runs on unpaved ground needs a different answer, and we would rather say the leg configuration is wrong for that lane than ship it and let the yard decide.
- Leg position against the wheel. A leg welded at mid-span protects nothing. On this build the four legs sit at the base corners, directly outboard of the caster brackets, so the corner that loses its wheel is the corner that lands.
- Caster set and corner load. 6-inch iron-core polyurethane, two braked swivel and two fixed, is the mainstream configuration; 5-inch, 8-inch and six-wheel sets exist on other drawings. The rating has to be matched to your corner load, and that figure comes out of your panel list, not out of the product name.
- Geometry and pack. Storage width is a parameter — current drawings run 180 to 420 mm per side on a 90° cradle, and wider storage trades against frame height. Load figures recorded on this build run 1000 to 3000 kg distributed with single-side figures around 1.5 t; anything above that is a drawing review rather than a catalogue selection.
What we will not do is call the leg a certificate. The geometry, the welds and the section are what we can show and document; anything a buyer needs for a conformity or insurance file is requested per order and answered with the drawing for that build. Send the panel sizes, the unit weights, the floor you actually roll on and the handling method — push, forklift or overhead — and the leg clearance, caster set and base section get confirmed against those numbers.
