WhatsApp Telegram
CONTACT
AGrack Heavy-Duty Custom Configuration

AGrack Heavy-Duty Glass Storage Transport Rack for 2000–2500 kg Loads

When the standard 1500 kg dynamic load is not enough, Agrack can be engineered for a customer-specific 2000–2500 kg load while retaining its collapsible return-logistics function. The heavy-duty version is intended for large architectural glass, thick glass and other high-mass sheet loads—not as an automatic replacement for the standard configuration.

Submit Single-Rack Load Requirement
3D product render demonstrating two loaded galvanized glass stillages stacked vertically to optimize high-density warehouse floor space.

More load capacity, without giving up fold-flat recovery

The decision is not simply “choose a bigger number.” A heavy-duty Agrack starts with the actual glass weight per rack, load distribution, glass dimensions, handling method, floor condition and required stacking mode. The frame can retain the slide-rail pin folding mechanism, self-locking cup feet and rubber-lined glass contact points, but the rated configuration and operating rules must be confirmed for the application. For customers moving oversized IGU, thick tempered glass or dense stone-like sheet loads, this creates a controlled alternative to disposable wooden crates or a permanently installed steel A-frame.

LOAD & CONFIGURATION GATE

Standard Agrack or heavy-duty Agrack?

Use the standard configuration when the single-rack dynamic load stays within 1500 kg. Move to a heavy-duty review when the real load, not the theoretical glass volume, exceeds that limit.

Compare the operating boundary before requesting a quotation.
Decision pointStandard AgrackHeavy-duty Agrack
Single-rack load1500 kg dynamic load referenceCustomer-specific 2000–2500 kg configuration, subject to engineering review
Typical glassArchitectural glass, IGU and window panels within the standard load envelopeLarge-format architectural glass, thick glass or concentrated loads that exceed the standard envelope
Loaded stackingStandard operating arrangement may support up to 3 tiers where the approved configuration and site rules allowLoaded stacking is reduced to 2 tiers to control height, center of gravity and transferred load
Load pathStacking feet locate on the lower rack’s steel uprights; glass is supported by protected contact surfacesThe same vertical load-path principle is retained, with the upright, base and locking details reviewed for the requested load
Folded returnFoldable frame for compact empty-rack storage and return transportFoldable function is retained; folded dimensions, handling clearances and return quantity are confirmed against the reinforced configuration
What is confirmedStandard product specificationFinal capacity, stacking rule and handling method are confirmed per single-rack requirement—not assumed from a project example
3D product render on white background showing a single galvanized Agrack collapsible stillage folded flat to minimize shipping volume.

Request a configuration, not a generic catalogue number

Send the maximum glass weight per rack and the way the rack will be moved. We will separate the standard option from a heavy-duty configuration and state the permitted loaded stacking level.

  • 2000–2500 kg target load range for review
  • Two-high loaded stacking rule for heavy-duty use
  • Folded return logistics retained where the design permits
Get Heavy-Duty Configuration
ENGINEERING LOGIC

Why the heavy-duty version is limited to two loaded tiers

The lower stacking limit is a deliberate operating control. A heavier rack load increases the consequence of height, floor irregularity and handling error; keeping loaded stacks to two tiers reduces the combined center-of-gravity and stability challenge.

The upright carries the stack—not the glass

When the upper rack is correctly seated, its self-locking cup feet locate on the lower rack’s steel uprights. The static stack load is intended to travel vertically through the Q235 steel columns, base structure and floor. The glass remains positioned against the EPDM-lined supports rather than becoming the compression member between racks. This logic only works when the rack is level, the feet are fully seated, the safety pins are installed and the front stop block remains in place.

Real warehouse photograph of two loaded galvanized glass storage stillages stacked two-high, filled with large insulated glass units.

Reinforce the load path while preserving handling and folding

The heavy-duty discussion focuses on the parts that see the load: steel uprights, base frame, welded stacking feet, forklift pockets, hinge and locking details. The slide-rail pin folding mechanism and steel-cored EPDM protection can remain part of the use case, but they do not authorize a higher rating by themselves. During operation, use the approved forklift entry points, secure the glass with the specified straps, keep the load within the rack envelope and never fold or move a loaded rack unless the written handling procedure allows it.

Close-up photograph of galvanized Agrack leg showing welded stacking cup foot, upright square tube, and folding hinge slide slot.

When 2000+ kg is the right conversation

Choose a heavy-duty review when one rack will carry large-format building glass, thick tempered glass, heavy IGU assemblies or another concentrated sheet load above the 1500 kg standard reference. It is also relevant when production-line-to-site handling must stay unitized and repacking would add labor or damage exposure.

When the standard or another system is better

Stay with the standard Agrack when the verified dynamic load is within 1500 kg and three-tier storage is an operational priority. Use a fixed A-frame or another engineered support when the rack will not be moved, when the floor cannot accept the transferred load, when the glass geometry exceeds the frame envelope, or when the site cannot enforce two-tier stacking and safe-pinning procedures. A disposable crate may still suit a one-way shipment with no return cycle.

Submit one rack’s load requirement for a heavy-duty configuration

Include maximum glass weight, glass dimensions and thickness, load distribution, forklift or crane handling method, required loaded tiers, floor condition and whether empty racks must be returned folded. We will confirm whether the standard Agrack, a 2000–2500 kg configuration or another support format fits the job.

Request Heavy-Duty Agrack Configuration

Related configurations: standard glass storage rack reference and folding glass transport rack options.

Email
get a quote
whatsapp